Tires 101: An Introduction: Difference between revisions

(7 intermediate revisions by the same user not shown)

Line 6:

Tires are a mysterious thing. Think about it: A reinforced bladder with about thirty pounds of air is all that keeps your motorcycle from rolling on its bare metal rims. That thin bit of rubber is what lets you get out there and enjoy a good ride. Obviously, it pays to know about your tires.

There are a few basic elements to consider when looking at tires. The type of tire, the size, the profile, and the aspect ratio all affect the behaviour of the tire, and thus the behaviour of the ~~bike. We'll take these elements and go through them and the effect that they can have on your~~ bike.

There are a few basic elements to consider when looking at tires. The type of tire, the size, the profile, and the aspect ratio all affect the behaviour of the tire, and thus the behaviour of the bike.

==Tire sizing==

Line 29:

The aspect ratio is approximately how tall the tire is in relationship to its width. Thus, a 120/80 tire is about 96 mm tall, from the bead to the tread surface (120 x 0.8 = 96). [[Ride height and different tire sizes|See here]] for more information on tire height.

The speed rating indicates at what maximum speed the tire is considered safe for continuous use. In this instance, the V stands for speeds up to 149 mph. A table of speed ratings is listed below.

The [[Speed ratings|speed rating]] indicates at what maximum speed the tire is considered safe for continuous use. In this instance, the V stands for speeds up to 149 mph. A table of speed ratings is listed below.

The last number is the diameter of the wheel that the tire is intended for. In this case, we are talking about a 16 inch rim for the tire.

Line 184:

The profile of the tire is the cross sectional shape. It is affected by several elements. The aspect ratio, wheel width, width of the tire, and the manufacturer's intentions for the tire all affect the profile. The profile in turn affects the handling. A triangular profile will cause the bike to turn in more easily, but may make it a little more prone to tucking or falling into the turn. On the other hand, a rounder profile may be a little more difficult to turn in, but might have a little more linear response to steering inputs. This is to a great extent motorcycle dependent; some bikes may like a particular tire, while others may not.

All in all, this means that a wider tire will tend to steer more heavily, but will also offer more traction. A larger rim will also steer slower, as will a broad, relatively flat tire.

All in all, this means that a wider tire will tend to steer more heavily, but will also offer more traction, [[About wider tires|to a point]]. A larger rim will also steer slower, as will a broad, relatively flat tire.

==Buying the right size==

So, what does all this mean when it comes time to go out and buy the tire? Well, it means a lot. First of all, in many cases the tire selection may be limited by the wheels on the bike, or the age and style of the bike. An excellent example of these limitations is found when attempting to find tires for a pre-1994 EX500 or a Ninja 600. Both of these bikes have relatively narrow 16 inch rims, but they are also meant to be ~~more~~ sporting motorcycles. The selection of quality rubber for these bikes is pretty limited. You will find the same thing when you go looking for tires for the Ninja 250.

So, what does all this mean when it comes time to go out and buy the tire? Well, it means a lot. First of all, in many cases the tire selection may be limited by the wheels on the bike, or the age and style of the bike. An excellent example of these limitations is found when attempting to find tires for a pre-1994 EX500 or Ninja 600. Both of these bikes have relatively narrow 16 inch rims, but they are also meant to be sporting motorcycles. The selection of quality rubber for these bikes is pretty limited. You will find the same thing when you go looking for tires for the Ninja 250.

In other cases, while the hardware may be capable of supporting a more current tire, the optimal sizes are not available. A good example of this is the 1986 VF1000R. It has a 2.75x16 front wheel and a 3.50x17 rear wheel. The fitment of rear tires is not a problem -- any of the quality 140~~, 150, or 160~~ width radials will fit nicely. The slightly narrow front, however, really works best with a bias-ply tire. As for the EX250, there are good tires available, but they're not necessarily the "perfect" size. That's where the above charts come in handy. (See also the [[What tire makes are available that fit the 250?|Tire Models Page]]).

In other cases, while the hardware may be capable of supporting a more current tire, the optimal sizes are not available. A good example of this is the 1986 VF1000R. It has a 2.75x16 front wheel and a 3.50x17 rear wheel. The fitment of rear tires is not a problem -- any of the quality 140 width radials will fit nicely. The slightly narrow front, however, really works best with a bias-ply tire. As for the EX250, there are good tires available, but they're not necessarily the "perfect" size. That's where the above charts come in handy. (See also the [[What tire makes are available that fit the 250?|Tire Models Page]]).

==Radials==

And that brings us to an important matter for tire buyers ~~-- should~~ I buy a radial tire? The answer is a firm "maybe". (The answer for ~~EX 250~~ owners is a firm "uhh, forget it.") ~~First of all, it helps to know~~ the difference between a radial and a bias ply tire~~. To understand the difference~~, it helps to know a little bit about tire construction.

And that brings us to an important matter for tire buyers: Should I buy a radial tire? The answer is a firm "maybe". (The answer for EX250 owners is a firm "uhh, forget it.") To understand the difference between a radial and a bias ply tire, it helps to know a little bit about tire construction.

A tire is nothing more than a bladder for air. It is made of rubber reinforced with some sort of fiber (~~once~~ they were reinforced with canvas, now they're reinforced with kevlar ~~-- times~~ have changed). The rubber keeps the air in, and the fiber keeps the tire together, in addition to ~~importing~~ shape characteristics to the tire. ~~The fibers~~ are ~~layed out~~ in layers, each layer consisting of fibers ~~lain~~ in parallel, ~~and~~ impregnated with rubber. The final element is the bead, which is simply a wire put around the edge of the tire to help it clamp to the rim.

A tire is nothing more than a bladder for air. It is made of rubber reinforced with some sort of fiber. (Once they were reinforced with canvas; now they're reinforced with kevlar. Times have changed). The rubber keeps the air in, and the fiber keeps the tire together, in addition to imparting shape characteristics to the tire. Tires are constructed in layers, each layer consisting of fibers laid in parallel, then impregnated with rubber. The final element is the bead, which is simply a wire put around the edge of the tire to help it clamp to the rim.

The way these layers are placed on the tire is what determines whether the tire is a bias-ply or radial tire. In short, a radial is a tire where the threads in the ply are ~~lain perpendicularly~~ to the bead. This gives them the appearance of radiating from the center of the tire, thus the term radial. Bias ply tires are a little different, because the angle of the fibers is at a bias to the bead, usually at an angle of about 70 degrees. For reference, a "zero degree" layer would be a belt around the circumference of the tire.

The way these layers are placed on the tire is what determines whether the tire is a bias-ply or radial tire. In short, a radial is a tire where the threads in the ply are perpendicular to the bead. This gives them the appearance of radiating from the center of the tire, thus the term radial. Bias ply tires are a little different, because the angle of the fibers is at a bias to the bead, usually at an angle of about 70 degrees. For reference, a "zero degree" layer would be a belt around the circumference of the tire.

Okay, so what does it mean? Well, a bias-ply tire requires a minimum of two layers to support the sidewall and the tread. The layers are fairly stiff, and essentially must scissor against each other to flex. This makes the tire run hotter. A radial tire needs only one ply, and thus is not only softer, but runs much cooler, and weighs less to boot. Advantages all around -- lighter, cooler, more compliant. This means that not only can you run a softer compound for radials, but it will provide better grip since it can conform to the road better. Great!

Okay, so what does it mean? Well, a bias-ply tire requires a minimum of two layers to support the sidewall and the tread. The layers are fairly stiff, and essentially must scissor against each other to flex. This makes the tire run hotter. A radial tire needs only one ply, and thus is not only softer but runs much cooler, and weighs less to boot. Advantages all around: lighter, cooler, more compliant. This means that not only can you run a softer compound for radials, but it will provide better grip since it can conform to the road better. Great!

But wait! There's a catch -- radial tires require wider rims to support the same tire width. That means that a 120/80 bias ply tire would work on a 2.5 inch rim, but a 120/80 radial would need a 3.0 inch rim to support it properly. Why does a radial need a wider rim? In simplest terms, a radial tends to have a softer sidewall, and a wider rim with a similar aspect radial puts less load on the sidewall, causing it to distort less under load. Most radials are designed for wider wheels, and putting them on a narrower rim will distort the cross-section of the tire and affect the handling of the bike -- almost always negatively.

@@ Line 6: / Line 6: @@
 Tires are a mysterious thing. Think about it: A reinforced bladder with about thirty pounds of air is all that keeps your motorcycle from rolling on its bare metal rims. That thin bit of rubber is what lets you get out there and enjoy a good ride. Obviously, it pays to know about your tires.
-There are a few basic elements to consider when looking at tires. The type of tire, the size, the profile, and the aspect ratio all affect the behaviour of the tire, and thus the behaviour of the bike. We'll take these elements and go through them and the effect that they can have on your bike.
+There are a few basic elements to consider when looking at tires. The type of tire, the size, the profile, and the aspect ratio all affect the behaviour of the tire, and thus the behaviour of the bike.
 ==Tire sizing==
@@ Line 29: / Line 29: @@
 The aspect ratio is approximately how tall the tire is in relationship to its width. Thus, a 120/80 tire is about 96 mm tall, from the bead to the tread surface (120 x 0.8 = 96). [[Ride height and different tire sizes|See here]] for more information on tire height.
-The speed rating indicates at what maximum speed the tire is considered safe for continuous use. In this instance, the V stands for speeds up to 149 mph. A table of speed ratings is listed below.
+The [[Speed ratings|speed rating]] indicates at what maximum speed the tire is considered safe for continuous use. In this instance, the V stands for speeds up to 149 mph. A table of speed ratings is listed below.
 The last number is the diameter of the wheel that the tire is intended for. In this case, we are talking about a 16 inch rim for the tire.
@@ Line 184: / Line 184: @@
 The profile of the tire is the cross sectional shape. It is affected by several elements. The aspect ratio, wheel width, width of the tire, and the manufacturer's intentions for the tire all affect the profile. The profile in turn affects the handling. A triangular profile will cause the bike to turn in more easily, but may make it a little more prone to tucking or falling into the turn. On the other hand, a rounder profile may be a little more difficult to turn in, but might have a little more linear response to steering inputs. This is to a great extent motorcycle dependent; some bikes may like a particular tire, while others may not.
-All in all, this means that a wider tire will tend to steer more heavily, but will also offer more traction. A larger rim will also steer slower, as will a broad, relatively flat tire.
+All in all, this means that a wider tire will tend to steer more heavily, but will also offer more traction, [[About wider tires|to a point]]. A larger rim will also steer slower, as will a broad, relatively flat tire.
 ==Buying the right size==
-So, what does all this mean when it comes time to go out and buy the tire? Well, it means a lot. First of all, in many cases the tire selection may be limited by the wheels on the bike, or the age and style of the bike. An excellent example of these limitations is found when attempting to find tires for a pre-1994 EX500 or a Ninja 600. Both of these bikes have relatively narrow 16 inch rims, but they are also meant to be more sporting motorcycles. The selection of quality rubber for these bikes is pretty limited. You will find the same thing when you go looking for tires for the Ninja 250.
+So, what does all this mean when it comes time to go out and buy the tire? Well, it means a lot. First of all, in many cases the tire selection may be limited by the wheels on the bike, or the age and style of the bike. An excellent example of these limitations is found when attempting to find tires for a pre-1994 EX500 or Ninja 600. Both of these bikes have relatively narrow 16 inch rims, but they are also meant to be sporting motorcycles. The selection of quality rubber for these bikes is pretty limited. You will find the same thing when you go looking for tires for the Ninja 250.
-In other cases, while the hardware may be capable of supporting a more current tire, the optimal sizes are not available. A good example of this is the 1986 VF1000R. It has a 2.75x16 front wheel and a 3.50x17 rear wheel. The fitment of rear tires is not a problem -- any of the quality 140, 150, or 160 width radials will fit nicely. The slightly narrow front, however, really works best with a bias-ply tire. As for the EX250, there are good tires available, but they're not necessarily the "perfect" size. That's where the above charts come in handy. (See also the [[What tire makes are available that fit the 250?|Tire Models Page]]).
+In other cases, while the hardware may be capable of supporting a more current tire, the optimal sizes are not available. A good example of this is the 1986 VF1000R. It has a 2.75x16 front wheel and a 3.50x17 rear wheel. The fitment of rear tires is not a problem -- any of the quality 140 width radials will fit nicely. The slightly narrow front, however, really works best with a bias-ply tire. As for the EX250, there are good tires available, but they're not necessarily the "perfect" size. That's where the above charts come in handy. (See also the [[What tire makes are available that fit the 250?|Tire Models Page]]).
 ==Radials==
-And that brings us to an important matter for tire buyers -- should I buy a radial tire? The answer is a firm "maybe". (The answer for EX 250 owners is a firm "uhh, forget it.") First of all, it helps to know the difference between a radial and a bias ply tire. To understand the difference, it helps to know a little bit about tire construction.
+And that brings us to an important matter for tire buyers: Should I buy a radial tire? The answer is a firm "maybe". (The answer for EX250 owners is a firm "uhh, forget it.") To understand the difference between a radial and a bias ply tire, it helps to know a little bit about tire construction.
-A tire is nothing more than a bladder for air. It is made of rubber reinforced with some sort of fiber (once they were reinforced with canvas, now they're reinforced with kevlar -- times have changed). The rubber keeps the air in, and the fiber keeps the tire together, in addition to importing shape characteristics to the tire. The fibers are layed out in layers, each layer consisting of fibers lain in parallel, and impregnated with rubber. The final element is the bead, which is simply a wire put around the edge of the tire to help it clamp to the rim.
+A tire is nothing more than a bladder for air. It is made of rubber reinforced with some sort of fiber. (Once they were reinforced with canvas; now they're reinforced with kevlar. Times have changed). The rubber keeps the air in, and the fiber keeps the tire together, in addition to imparting shape characteristics to the tire. Tires are constructed in layers, each layer consisting of fibers laid in parallel, then impregnated with rubber. The final element is the bead, which is simply a wire put around the edge of the tire to help it clamp to the rim.
-The way these layers are placed on the tire is what determines whether the tire is a bias-ply or radial tire. In short, a radial is a tire where the threads in the ply are lain perpendicularly to the bead. This gives them the appearance of radiating from the center of the tire, thus the term radial. Bias ply tires are a little different, because the angle of the fibers is at a bias to the bead, usually at an angle of about 70 degrees. For reference, a "zero degree" layer would be a belt around the circumference of the tire.
+The way these layers are placed on the tire is what determines whether the tire is a bias-ply or radial tire. In short, a radial is a tire where the threads in the ply are perpendicular to the bead. This gives them the appearance of radiating from the center of the tire, thus the term radial. Bias ply tires are a little different, because the angle of the fibers is at a bias to the bead, usually at an angle of about 70 degrees. For reference, a "zero degree" layer would be a belt around the circumference of the tire.
-Okay, so what does it mean? Well, a bias-ply tire requires a minimum of two layers to support the sidewall and the tread. The layers are fairly stiff, and essentially must scissor against each other to flex. This makes the tire run hotter. A radial tire needs only one ply, and thus is not only softer, but runs much cooler, and weighs less to boot. Advantages all around -- lighter, cooler, more compliant. This means that not only can you run a softer compound for radials, but it will provide better grip since it can conform to the road better. Great!
+Okay, so what does it mean? Well, a bias-ply tire requires a minimum of two layers to support the sidewall and the tread. The layers are fairly stiff, and essentially must scissor against each other to flex. This makes the tire run hotter. A radial tire needs only one ply, and thus is not only softer but runs much cooler, and weighs less to boot. Advantages all around: lighter, cooler, more compliant. This means that not only can you run a softer compound for radials, but it will provide better grip since it can conform to the road better. Great!
 But wait! There's a catch -- radial tires require wider rims to support the same tire width. That means that a 120/80 bias ply tire would work on a 2.5 inch rim, but a 120/80 radial would need a 3.0 inch rim to support it properly. Why does a radial need a wider rim? In simplest terms, a radial tends to have a softer sidewall, and a wider rim with a similar aspect radial puts less load on the sidewall, causing it to distort less under load. Most radials are designed for wider wheels, and putting them on a narrower rim will distort the cross-section of the tire and affect the handling of the bike -- almost always negatively.