Servicing the swingarm: Difference between revisions

(2 intermediate revisions by the same user not shown)

Line 20:

:This grease is an excellent choice; it is a lithium soap and contains molybdenum disulphide:

:[[Image:grease2.jpg|120px]][[Image:grease.jpg|120px]]

:[[Image:grease2.jpg|120px]] [[Image:grease.jpg|120px]]

*O-rings. Kawasaki part #92055-1215 (size 19.8 X 2.2) The Unitrak linkage uses a LOT of O-rings around the bushings, and it isn't that unusual to find some damaged ones on a high-miles bike. It is imperative that these O-rings are in good shape. You normally don't need any, but stalling the job for 3-4 days because you're missing a $2 part would be bad.

Line 41:

[[Image:wheelremoved.jpg|150px]]

3) Remove the nuts from the swingarm pivot (22mm), lower shock mount (19mm) and upper tie rod arms (19mm), but do not remove the bolts or pivot shaft. The easiest way to remove the 19mm nuts is to "lock" them in place with a 19mm open-~~ended~~ wrench, then spin their corresponding bolt heads with a 17mm socket, extension, and breaker bar (or ratchet + piece of pipe).

3) Remove the nuts from the swingarm pivot (22mm), lower shock mount (19mm) and upper tie rod arms (19mm), but do not remove the bolts or pivot shaft. The easiest way to remove the 19mm nuts is to "lock" them in place with a 19mm open-end wrench, then spin their corresponding bolt heads with a 17mm socket, extension, and breaker bar (or ratchet + piece of pipe).

[[Image:swingarmclose.jpg|150px]] [[Image:pivotnutremoved.jpg|150px]]

Line 57:

Remove the rubber chain guard from the swingarm. Wipe off any crud from it and the swingarm. If you are planning to re-paint the swingarm when you see how horrible it looks, Duplicolor [http://www.amazon.com/Dupli-Color-HWP101-Silver-Performance-Wheel/dp/B000B6DFZ0 silver wheel paint], available at fine Wal-Mart stores everywhere, is a perfect match.

7) Remove the plastic rings from either end of the pivot shaft and clean them. They pop out easily with your fingernails.

7) Remove the plastic rings from either end of the pivot shaft sleeve and clean them. They pop out easily with your fingernails.

8) Remove the pivot shaft from the front of the swingarm by sliding it out one end.

8) Remove the pivot shaft sleeve from the front of the swingarm by sliding it out one end.

9) Wash the pivot shaft, pivot shaft sleeve, and needle bearings with kerosene and dry thoroughly.

@@ Line 20: / Line 20: @@
 :This grease is an excellent choice; it is a lithium soap and contains molybdenum disulphide:
-:[[Image:grease2.jpg|120px]][[Image:grease.jpg|120px]]
+:[[Image:grease2.jpg|120px]] [[Image:grease.jpg|120px]]
 *O-rings. Kawasaki part #92055-1215 (size 19.8 X 2.2) The Unitrak linkage uses a LOT of O-rings around the bushings, and it isn't that unusual to find some damaged ones on a high-miles bike. It is imperative that these O-rings are in good shape. You normally don't need any, but stalling the job for 3-4 days because you're missing a $2 part would be bad.
@@ Line 41: / Line 41: @@
 [[Image:wheelremoved.jpg|150px]]
-) Remove the nuts from the swingarm pivot (22mm), lower shock mount (19mm) and upper tie rod arms (19mm), but do not remove the bolts or pivot shaft. The easiest way to remove the 19mm nuts is to "lock" them in place with a 19mm open-ended wrench, then spin their corresponding bolt heads with a 17mm socket, extension, and breaker bar (or ratchet + piece of pipe).
+) Remove the nuts from the swingarm pivot (22mm), lower shock mount (19mm) and upper tie rod arms (19mm), but do not remove the bolts or pivot shaft. The easiest way to remove the 19mm nuts is to "lock" them in place with a 19mm open-end wrench, then spin their corresponding bolt heads with a 17mm socket, extension, and breaker bar (or ratchet + piece of pipe).
 [[Image:swingarmclose.jpg|150px]] [[Image:pivotnutremoved.jpg|150px]]
@@ Line 57: / Line 57: @@
 Remove the rubber chain guard from the swingarm. Wipe off any crud from it and the swingarm. If you are planning to re-paint the swingarm when you see how horrible it looks, Duplicolor [http://www.amazon.com/Dupli-Color-HWP101-Silver-Performance-Wheel/dp/B000B6DFZ0 silver wheel paint], available at fine Wal-Mart stores everywhere, is a perfect match.
-) Remove the plastic rings from either end of the pivot shaft and clean them. They pop out easily with your fingernails.
+) Remove the plastic rings from either end of the pivot shaft sleeve and clean them. They pop out easily with your fingernails.
-) Remove the pivot shaft from the front of the swingarm by sliding it out one end.
+) Remove the pivot shaft sleeve from the front of the swingarm by sliding it out one end.
 ) Wash the pivot shaft, pivot shaft sleeve, and needle bearings with kerosene and dry thoroughly.