Replacing the wheel bearings: Difference between revisions

Line 36:

If you don't want to spend the money on the tool set, and many people don't, you can get by with a drift (aka a punch), or a long 3/8 drive extension. Some have had success with a BFSD (large screwdriver). Since you're not trying to save the old ones, feel free to bash away at the inner race. The tube that runs through the wheel doesn't usually completely cover the inner race, so you can kind of get a purchase on it, beating the bearing out from the opposite side of the wheel. The down side is that you have to move around the race to get the bearing out evenly, and you're going to have to be careful, because the drift will probably slip off and bust your knuckles a few times (think "leather gloves").

For putting the new bearings in, all you need to do is hammer them in. '''Important:''' ''You only want to put pressure on the outer race (the outside rim of the bearing)''. You can do this with a ~~[http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=92387~~ bearing seating kit], or a socket that you carefully hold in place so you don't hit the bearings. You can also disassemble an old bearing and use only the outer race, with a piece of wood on top of it, to drive the new bearing in.

For putting the new bearings in, all you need to do is hammer them in. '''Important:''' ''You only want to put pressure on the outer race (the outside rim of the bearing)''. You can do this with a bearing seating kit (check auto parts stores), or a socket that you carefully hold in place so you don't hit the bearings. You can also disassemble an old bearing and use only the outer race, with a piece of wood on top of it, to drive the new bearing in.

One tool that makes installation easier (rent/borrow if you don't have one) is a forced air shop heater. Hold the wheel hub in front of it until it's around 200 deg F. The expansion from the heat makes it marginally easier to remove the old bearings. This also works for installation. Leave the new bearings in your freezer until you're ready for installation, and install them into the heated hub. It reduces the amount of interference just enough to make it easy to tap in the new bearings.

The new bearings should last significantly longer than your stock ones.

@@ Line 36: / Line 36: @@
 If you don't want to spend the money on the tool set, and many people don't, you can get by with a drift (aka a punch), or a long 3/8 drive extension. Some have had success with a BFSD (large screwdriver). Since you're not trying to save the old ones, feel free to bash away at the inner race. The tube that runs through the wheel doesn't usually completely cover the inner race, so you can kind of get a purchase on it, beating the bearing out from the opposite side of the wheel. The down side is that you have to move around the race to get the bearing out evenly, and you're going to have to be careful, because the drift will probably slip off and bust your knuckles a few times (think "leather gloves").
-For putting the new bearings in, all you need to do is hammer them in. '''Important:''' ''You only want to put pressure on the outer race (the outside rim of the bearing)''. You can do this with a [http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=92387 bearing seating kit], or a socket that you carefully hold in place so you don't hit the bearings. You can also disassemble an old bearing and use only the outer race, with a piece of wood on top of it, to drive the new bearing in.
+For putting the new bearings in, all you need to do is hammer them in. '''Important:''' ''You only want to put pressure on the outer race (the outside rim of the bearing)''. You can do this with a bearing seating kit (check auto parts stores), or a socket that you carefully hold in place so you don't hit the bearings. You can also disassemble an old bearing and use only the outer race, with a piece of wood on top of it, to drive the new bearing in.
 One tool that makes installation easier (rent/borrow if you don't have one) is a forced air shop heater. Hold the wheel hub in front of it until it's around 200 deg F. The expansion from the heat makes it marginally easier to remove the old bearings. This also works for installation. Leave the new bearings in your freezer until you're ready for installation, and install them into the heated hub. It reduces the amount of interference just enough to make it easy to tap in the new bearings.
 The new bearings should last significantly longer than your stock ones.