Heated cold-weather gear: Difference between revisions

Line 80:

[[Image:IMG_0740.jpg|150px]]

'''One important thing to remember:''' The aux/accessory wires get power ALL of the time, even when there is no key in the ignition. This page on [http://www.canyonchasers.net/shop/generic/relay.php Canyon Chasers] has good ideas on how to use relays so you can turn off the accessories when the key goes off. This bike has the high/off/low switch mounted on the right side fairing. Just consider how easy it would be to forget to shut off the switch when it is cold out and you want to be in.

'''One important thing to remember:''' The aux/accessory wires get power ALL of the time, even when there is no key in the ignition. This page on [http://www.canyonchasers.net/shop/generic/relay.php Canyon Chasers] has good ideas on how to use relays so you can turn off the accessories when the key goes off. This bike has the high/off/low switch mounted on the right side fairing. Just consider how easy it would be to forget to shut off the switch when it is cold out and you want to be in. You could also [[Making your accessory wires 'switched'|modify your accessory wires]].

Some manufacturers say to glue the grips to the heaters, but that's not necessary. They stay put just fine. Just mount them [[I want to get some new grips|in the usual way]].

Line 86:

'''Addendum'''

After running the battery dry by forgetting to turn off the switch, our man decided to put a warning light into his system. If you don't want to add a relay (above), then you can install an LED light. Buy a 12v red (or other bright color) LED, a 330 ohm resistor, and an LED holder. Solder the resistor to the LED in the holder, because that way the current is regulated by it and cannot peak and destroy the LED. The LED must be in parallel with the heated grips and not in series, otherwise the current drawn by the grips will destroy the LED.

After running the battery dry by forgetting to turn off the switch, our man decided to put a warning light into his system. If you don't want to add a relay or modify your accessory wires (above), then you can install an LED light. Buy a 12v red (or other bright color) LED, a 330 ohm resistor, and an LED holder. Solder the resistor to the LED in the holder, because that way the current is regulated by it and cannot peak and destroy the LED. The LED must be in parallel with the heated grips and not in series, otherwise the current drawn by the grips will destroy the LED.

This is a picture of the circuit. For your own mental health, pay no attention to the -- and + signs on this diagram. Just know that, like all bike/auto applications, power flows from the + (red) pole on the battery to the -- (ground). Wire it so that the switch receives power before the heated grips. This ensures that power will have to go through the 330 ohm resistor before reaching the LED.

@@ Line 80: / Line 80: @@
 [[Image:IMG_0740.jpg|150px]]
-'''One important thing to remember:'''  The aux/accessory wires get power ALL of the time, even when there is no key in the ignition. This page on [http://www.canyonchasers.net/shop/generic/relay.php Canyon Chasers] has good ideas on how to use relays so you can turn off the accessories when the key goes off. This bike has the high/off/low switch mounted on the right side fairing. Just consider how easy it would be to forget to shut off the switch when it is cold out and you want to be in.
+'''One important thing to remember:'''  The aux/accessory wires get power ALL of the time, even when there is no key in the ignition. This page on [http://www.canyonchasers.net/shop/generic/relay.php Canyon Chasers] has good ideas on how to use relays so you can turn off the accessories when the key goes off. This bike has the high/off/low switch mounted on the right side fairing. Just consider how easy it would be to forget to shut off the switch when it is cold out and you want to be in. You could also [[Making your accessory wires 'switched'|modify your accessory wires]].
 Some manufacturers say to glue the grips to the heaters, but that's not necessary. They stay put just fine. Just mount them [[I want to get some new grips|in the usual way]].
@@ Line 86: / Line 86: @@
 '''Addendum'''
-After running the battery dry by forgetting to turn off the switch, our man decided to put a warning light into his system. If you don't want to add a relay (above), then you can install an LED light. Buy a 12v red (or other bright color) LED, a 330 ohm resistor, and an LED holder. Solder the resistor to the LED in the holder, because that way the current is regulated by it and cannot peak and destroy the LED. The LED must be in parallel with the heated grips and not in series, otherwise the current drawn by the grips will destroy the LED.
+After running the battery dry by forgetting to turn off the switch, our man decided to put a warning light into his system. If you don't want to add a relay or modify your accessory wires (above), then you can install an LED light. Buy a 12v red (or other bright color) LED, a 330 ohm resistor, and an LED holder. Solder the resistor to the LED in the holder, because that way the current is regulated by it and cannot peak and destroy the LED. The LED must be in parallel with the heated grips and not in series, otherwise the current drawn by the grips will destroy the LED.
 This is a picture of the circuit. For your own mental health, pay no attention to the -- and + signs on this diagram. Just know that, like all bike/auto applications, power flows from the + (red) pole on the battery to the -- (ground). Wire it so that the switch receives power before the heated grips. This ensures that power will have to go through the 330 ohm resistor before reaching the LED.